Search results for "Ic testing"
showing 10 items of 283 documents
Generalised bisection method for optimum ultrasonic ray tracing and focusing in multi-layered structures
2021
Ultrasonic testing has been used for many decades, proving itself very efficient for detecting defects in many industrial sectors. The desire to apply ultrasonic testing to geometrically complex structures, and to anisotropic, inhomogeneous materials, together with the advent of more powerful electronics and software, is constantly pushing the applicability of ultrasonic waves to their limits. General ray tracing models, suitable for calculating the proper incident angle of single element probes and the proper time delay of phased array, are currently required. They can support the development of new imaging techniques, as Full Matrix Capture and Total Focusing Method, and the execution of …
Laser Ultrasonics Inspection for Defect Evaluation on Train Wheel
2019
Abstract Passengers’ safety and in-service life of wheelset axles play an important role in railway vehicles. For this reason, periodic inspections are necessary. Among non-destructive techniques, ultrasonic ones are widely applied in this field. The main disadvantage of conventional ultrasonic techniques is that the overall inspection of wheels requires the train to be put out-of-service and disassembly each part, which is time-consuming and expensive. In this paper, a non-conventional non-contact laser ultrasonic inspection for train wheels is proposed. The proposed method uses a laser interferometer to receive the ultrasonic wave without contact. The receiving system allows choosing the …
Effects of Thermal Neutron Irradiation on a Self-Refresh DRAM
2020
International audience; In this study, static and dynamic test methods were used to define the response of a self-refresh DRAM under thermal neutron irradiation. The neutron-induced failures were investigated and characterized by event cross-sections, soft-error rate and bitmaps evaluations, leading to an identification of permanent and temporarily stuck cells, block errors, and single-bit upsets.
Influence of an evoked pleasant consumption context on consumers’ hedonic evaluation for minimally processed cactus pear (Opuntia ficus-indica) fruit
2016
Awareness of the need to consider a consumption context when measuring the consumer's hedonic evaluation of a food product led researchers to investigate differences among responses given by consumers in different contexts. Previous studies measured the effects of evoking a consumption context, by using photographs or a written scenario, on hedonic evaluations of consumers for food products. This study investigated the influence of evoking a consumption context on hedonic evaluation of minimally processed cactus pear (Opuntia ficus-indica) fruit, using pictures and memories of pleasant personal experiences. A hedonic scale method for measuring food preferences was used. Hedonic evaluation o…
World-wide variation in Drosophila melanogaster sex pheromone: behavioural effects, genetic bases and potential evolutionary consequences
1996
0016-6707 (Print) Journal Article Research Support, Non-U.S. Gov't; In Drosophila melanogaster, male wing vibration, a key element of courtship behaviour, is most efficiently induced by a female-specific contact pheromone cis, cis 7,11 heptacosadiene (7,11 HD), which is the main mature female cuticular hydrocarbon in the CS laboratory strain. A study of 63 strains from around the world revealed that flies from Sub-Saharan Africa and the Caribbean are unique in showing low levels 7,11 HD and high levels of the position isomer 5,9 HD. This difference maps to chromosome III, perhaps indicating a simple genetic control of the 7,11 HD:5,9 HD ratio. Females from strains with high levels of 7,11 H…
Vision guided robotic inspection for parts in manufacturing and remanufacturing industry
2020
AbstractEnvironmental and commercial drivers are leading to a circular economy, where systems and components are routinely recycled or remanufactured. Unlike traditional manufacturing, where components typically have a high degree of tolerance, components in the remanufacturing process may have seen decades of wear, resulting in a wider variation of geometries. This makes it difficult to translate existing automation techniques to perform Non-Destructive Testing (NDT) for such components autonomously. The challenge of performing automated inspections, with off-line tool-paths developed from Computer Aided Design (CAD) models, typically arises from the fact that those paths do not have the r…
Ultrasonic phased array inspection of a Wire + Arc Additive Manufactured (WAAM) sample with intentionally embedded defects
2019
In this study, Wire + Arc Additive Manufacture (WAAM) was employed to manufacture a steel specimen with intentionally embedded defects which were subsequently used for calibration of an ultrasonic phased array system and defect sizing. An ABB robot was combined with the Cold Metal Transfer (CMT) Gas Metal Arc (GMA) process to deposit 20 layers of mild steel. Tungsten-carbide balls (ø1-3 mm) were intentionally embedded inside the additive structure after the 4th, 8th, 12th and 18th layers to serve as ultrasonic reflectors, simulating defects within the WAAM sample. An ultrasonic phased array system, consisting of a 5 MHz 64 Element phased array transducer, was used to inspect the WAAM sample…
High-temperature in-process inspection followed by 96-h robotic inspection of intentionally manufactured hydrogen crack in multi-pass robotic welding
2021
Abstract This investigation introduces two new techniques to quantitatively address the challenging problem of understanding Hydrogen Induced Cracking (HIC) in welding processes. The first technique is a novel procedure to create a known and controlled HIC in a welded sample. The second is an in-process monitoring technique to measure the initial formation and subsequent growth of the HIC in a multi-pass weld whilst being compatible with the high temperatures associated with the welding process. The HIC was initiated using a localised quenching method of the weld and its character was verified using both macrograph and microscopic investigations. During HIC initiation and growth, the sample…
Evaluation of Coded Excitations for Autonomous Airborne Ultrasonic Inspection
2019
Unmanned Aerial Vehicles (UAVs) are receiving increasing attention for use in Non-Destructive Testing due to their ability to access areas where manual inspection is not practical. Contact-based UAV ultrasonic inspections grant the opportunity to remotely monitor the structural health of an industrial asset with enhanced internal integrity information. Ultrasonic inspection is a Non-Destructive Testing (NDT) method conventionally used in corrosion mapping. Surface contacting ultrasonic transducers provide enhanced structural integrity information. However, due to near-surface aerodynamic effects, angular sensitivity of the ultrasound probe and alignment error during autonomous inspections, …
Type of chromosome abnormality affects embryo morphology dynamics.
2016
Objective To study the differences in the cleavage time between types of embryo chromosomal abnormalities and elaborate algorithm to exclude aneuploid embryos according to the likelihood to be euploid. Design Retrospective cohort study. Setting University affiliated private center. Patient(s) Preimplantational genetic screening patients (n = 112) including cases of advanced maternal age, repeated implantation failure, and recurrent miscarriage. A total of 485 embryos were analyzed. Intervention(s) None. Main Outcome Measure(s) All biopsied embryos were cultured in an incubator with time-lapse technology, cleavage timing from insemination to day 3 and all kinetic parameters that have been de…